Wyze cam status light flashing LIGHT BLUE

Wyze cam status light flashing LIGHT BLUE.

Hi, @GrandPaDave! The flashing blue LED indicates the cam is connected and setup is finished. If it isn’t connecting to your WiFi power cycle the cam.

Also, if you can provide a little more information about the issue you’re having the community may be able to assist better.

1 Like

From:

Want to revert the webcam firmware update?

  • Note: The “Solid Blue” in this case is not the same as the one normally seen on the camera. Instead, both the blue and yellow LEDs will
    be on at once, making it appear to be a lighter blue.*

This is what I was referring to as the blinking light blue light. Problem is it continues to blink - never turns blinking yellow or solid “dark” blue. To turn off I have to unplug power.

1 Like

The light blue light is the blue and orange together. The instructions caution not to confuse with this with

Thanks for clarifying. I haven’t actually tried using the Wyze cams for a webcam so I’m not much help. I’ll tag @tomp I believe he has experimented with it and may be able to help. Here are the support articles for the webcam firmware instructions.

Revert back to Wyze Cam

My Wyze webcams are blinking like this and are working as webcams, the light blue (blue and yellow led blinking together). What are you trying to get to work or change?

Edit/ and similar to what @StopICU33 said, the more information you provide will help in the troubleshooting process, if that’s the type of assistance you are looking for. There is the reference of “paint the picture”, so people looking on know exactly what is going on. I was thinking exactly what Stop initially replied with because you didn’t refer to the webcam feature at first. Thanks in advance!

Greetings Omgitstony,
Thanks for your response. I’m trying to reset this cam to factory original state. I tried RTSP, but didn’t care for the results. I want cam to function as before.

Regards,

Grandpa Dave (dadrett)


Omgitstony
Forum Maven

    May 20

dadrett41:
The light blue light is the blue and orange together. The instructions caution not to confuse with this with

My Wyze webcams are blinking like this and are working as webcams, the light blue (blue and yellow led blinking together). What are you trying to get to work or change?

@GrandPaDave , Sorry you are having problems. @StopICU33was right, I have used aV2 as both RTSP and a Webcam, and a Pan as a Webcam and reflashed the Firmware back to the standard Wyze Firmware. I had no problems with any of these steps with any of my cams. The instructions here are accurate.
Tips for the process:
Be sure to follow the steps exactly. Hold down the reset button on the bottom of the cam before plugging in the power cable and keep it held down until the light changes. Very important!
Be sure you have not renamed the demo.bin file to anything but that exact name. In Windows it’s possible to name it demo.bin.bin without knowing it.
Be sure you have downloaded the correct version of the firmware. V2 won’t work for Pan and vice-versa.
You may have to repeat the process a couple of times. I’ve been lucky but I’ve seen others have to try repeatedly. If all else fails, try swapping your SD card for a freshly formatted, 32GB card. Don’t format in a cam unless you have to. Use a PC and do a Deep or Full Format
This is the recommended format program for SD cards.

1 Like

Greetings tomp,

Thanks for your response. During the step where you hold down the setup button while plugging in USB cable and continue to hold button, I get a momentary yellow light and then light changes to blinking light (pale) blue (blue and yellow together) and it goes on forever.

The above was my reply to you until I looked at instructions again and discovered I wasn’t having to rename a folder from “something” to demo.bin. When I reread# Webcam Firmware Instructions

they end with:

  1. Once complete, the status light will flash yellow and blue at the same time (not alternating)

Wyze Cam will continue to flash yellow and blue at the same time if the webcam firmware is installed properly and the camera is turned on.

When I reread

Want to revert the webcam firmware update?

I must have missed importance of:

    1. Visit the Release Notes page for the latest Wyze Cam v2 firmware file.